Make yourself familiar with the basic functions of the units brief introduction: In the next screen form, please deactivate OB1 by deselecting the check mark. This is compared with the dc link voltage, derived in the inverter. When accessing drive parameters, help texts are associated with the parameter and the parameter values. The following procedure should be followed to set the P, I and D terms: Full digital control in microprocessor technology. T1 and T2 are variable, depending on ambient temperature.
| Uploader: | Kajigor |
| Date Added: | 10 July 2014 |
| File Size: | 55.39 Mb |
| Operating Systems: | Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X |
| Downloads: | 65554 |
| Price: | Free* [*Free Regsitration Required] |
The information in this publication, however, is regularly examined, and any necessary corrections appear in subsequent editions. Interactive control panel This is the central interactive area, and shows you the control and status simvois that are available to you for individual axis applications.
PLCforum.uz.ua
If the mains impedance is below this value the lifetime of the electrolytic capacitors could be reduced. To make things easier, it is recommended that the steps be executed in the suggested order, even when a different order would seem more expedient. Shows that internally stored parameter set is being accessed Param eter num ber The keys represent the same functions as on the standard operator panel except the Menu key, which selects the main menu screen at any time.
If you have 2 axes in your project, please add the additional values to DB Link to DIN 2 causes reverse rotation on left 10V output from the inverter may be used instead of the 15V. Param eter access 1 Figure siimovis. To make things easier, it is recommended that the steps be executed in the suggested order, even when a different order would seem more expedient.
SIEMENS MC使用入门_百度文库
If the error is not acceptable then the I term will need to be set. Exit this window by clicking on the "Work at" button and by opening "Control Desk" in the "Machine Control board" menu.
The drive converters must also supply these additional currents. If you have completed the installation as described, these settings will remain unchanged.
One output relay is used for operating the motor brake, the other is configured to report faults to the lift controller. They are convection-cooled, so a free space of at least mm must be left above and below the components to allow an unimpeded air flow. Finally, insert the following call in OB1: The contractual terms of this warranty are neither extended nor altered by this specification or its use.
If the motor in question is a Siemens simvis, it can be simply selected by Order No. Squirrel Cage Induction motors DA For special applications, the motor currents must be individually determined, and then the drive converter selected e. We have examined the contents of the publication for compliance with the hardware and software described therein.
Make yourself familiar with the basic functions of the units brief introduction: Clicking on the "Next" button screens the parameter assignment window for the motor sensor.
The advantage is that you can display and process interactive skmovis for several simovix at the same time. P1 - 7kW P2 - W T1 - 5 Seconds typical T2 - Seconds typical Protection In the event of a braking unit fault, it is possible for the resistor to become permanently connected, and to overheat.
Basic Installation and Start-up Guide for MASTERDRIVES MC and
Constant current and searching orientation region Whilst operating in this region and the output frequency is ramping up, the back emf from the motor begins to build up. A main switch or isolator should be provided to electrically isolate the unit from the line supply. Save the modified data block once again. simkvis
In order that these maximum permissible voltage peaks are not exceeded at the terminal boxes, the following conditions should be observed: You will find information for modified settings or additional synchronized axes in the Manual.
There are no restrictions regarding the parameters in specification DS This also allows the direction of rotation to be selected. The torque de-rating factor is not the same for all motors. Select the directory structure shown here: For further sikovis, see the following "Notes on how to proceed further". For optimum performance, there should be a good conductive bond between filter and metal mounting plate.
First, we want to create a new project with the corresponding file name in this case:
Comments
Post a Comment